使用中金属分离器**问题

使用中金属分离器**问题Safety problems in the use of metal separators

使用中金属分离器**问题

金属分离器主要由检测部分和剔除部分组成,应用电磁感原理来探测金属。所有金属包括铁和非铁都有很高的探测灵敏度。铁磁类金属进入探测区域将影

响探测区域的磁力线分布，进而影响了固定范围的磁通。非铁磁类金属进入探测区域将产生涡流效应，也会使探测区域的磁场分布发生变化,当金属杂质

通过时,会产品报警信号,输送给剔除部分,剔除部分翻板左右摆动,来剔除含有金属杂质的产品.从而实现金属杂质的彻底分离.

金属分离器使用中的**

操作和维护的**注意事项  

当本金属分离器工作时,应将机箱盖和电箱门关好,避免伤害危险和本机污染,延长使用寿命.所有贴在本机上的警示标识都必须清淅可见,不能以任何理由撕

除，入料口和出料口应由直径70mm的管连接，出口管*少应有90cm长如检测可爆炸的材料请阅读相关法规。如进行电子电气组件维修或气动组件维修,

一定要切断电源和气源.本操作说明书应易于获得和字迹清晰.

使用中金属分离器**问题只允许受过培训的技术人员操作和维修本机.

使用中金属分离器**问题潜在的危险 

在关闭电开关后,电箱由于外接电源仍然连接而可能处于带电状态.

另外,由于有压缩气缸的存在,切断气源后,气动组件仍会动作.
 

使用中金属分离器**问题未授权

在未经本公司授权的情况下,不允许擅自进行改装或维修工作.

不允许的操作

在的使用范围之外的操作是不允许的

在技术参数的范围之外的操作是不允许的.

不允许检测腐蚀性的材料和爆炸性的材料.

使用中金属分离器**问题使用方向

本设备主要应用于塑料工业，也可用于食品和化工行业。

本设备设计用于在垂直管线中自由下落的小团状材料(如粉状或粒状),进口应连接送料斗或管线.本设备应避免被蒸气,灰尘或类似物质包围,因为这可能影响

pvc电线的绝缘性.

使用中金属分离器**问题危险警示

在MSG3.3电箱中连接有主电源,它与外部交流电相连,因此在电箱的门内贴有危险警示。

当电源通电并且连接好气源时,打开设备的盖板是非常危险的, 因次在金属分离器的内部贴有危险警示

金属分离器的入口和出口高度都是80mm,手可以容易的碰到活门出口, 因次在金属分离器的出料口贴有危险警示

机箱盖可以保护操作人员不受伤害,如要打开盖板进行维修或保养请参阅4.4

在没有危险警示的地方可能出现的危险。

在没有危险警示的地方，有可能有静电或气动组件伤手的可能。

Safety problems in the use of metal separators
The metal separator is mainly composed of the detection part and the reject part, and uses the electromagnetic induction principle to detect the metal. All metals including iron and non-iron have a high detection sensitivity. Ferromagnetic metal into the detection area will affect the magnetic field distribution of the detection area, thus affecting the fixed range of magnetic flux. Non-ferromagnetic metal into the detection area will produce eddy current effect, will also make the detection area of the magnetic field distribution changes, when the metal impurities pass, the product alarm signal, sent to the removal part, remove part of the flap swing around to remove the Metal impurities in the product to achieve a complete separation of metal impurities.
The safety of the metal separator in use
Operation and maintenance of safety precautions
When the metal separator is in operation, the cover and the door of the cabinet should be closed to avoid the risk of injury and the local pollution and prolong the service life. All warning signs affixed to the machine must be clearly visible and can not be used for any reason The tearing, inlet and outlet should be connected by a pipe with a diameter of 70 mm. The outlet tube should be at least 90 cm long. If the explosive material is to be tested, please read the relevant regulations. If the electrical and electronic components repair or pneumatic components maintenance, be sure to cut off the power and gas source. The operating instructions should be easy to obtain and writing clear.
Use of metal separator safety issues Only trained technicians are allowed to operate and service the machine.
Use of metal separator safety problems potential hazards
After closing the electrical switch, the electrical box may be in a live state due to the external power supply being connected.
In addition, due to the presence of a compressed cylinder, cut off the gas source, the pneumatic components will still move.
 The use of metal separator safety issues are not authorized
In the case without authorization by the Company, no modification or repair work is allowed.
Not allowed to operate
Operation outside of the scope of 1 is not allowed
Operation outside the scope of the technical parameters is not allowed.
It is not allowed to detect corrosive materials and explosive materials.
Use of metal separator in the use of safety direction
The equipment is mainly used in the plastics industry, can also be used for food and chemical industry.
This equipment is designed for small pellets (such as powder or granules) that are free to fall in vertical lines and the inlet should be connected to hoppers or pipelines. This equipment should be protected from steam, dust or the like as this may affect pvc Insulation of wires.
Use of metal separator safety hazard hazard warning
In the MSG3.3 power box connected to the main power supply, which is connected with the external AC, so the door in the box with a dangerous warning.
When the power supply is energized and the air supply is connected, it is very dangerous to open the cover of the device. Because of the danger warning inside the metal separator
Metal separator inlet and outlet are 80mm height, the hand can easily touch the door exit, because the metal separator in the discharge port with a dangerous warning
The cover protects the operator from damage. If you want to open the cover for repair or maintenance, please refer to section 4.4
In danger of danger where there is no danger warning.
Where there is no danger warning, there may be static or pneumatic components injury may be.